GE IS200IGPAG2AED

Operating Parameters

Power Supply Voltage: 24V DC.

Line Input Type: Analog input (0 -- 10V).

Output Signal Type: 4 - 20mA.

Shaft Displacement Measurement Range: -5 mm to +5 mm.

The range of measurement for the diffusion expansion: -10 mm - 10 mm.

Accuracy: ±0.05 mm.

Response Time: beneath 50 ms.

Communication: RS485, Modbus protocol.

Operating Temp: 20° C - 60° C.

Product Features

High-Speed Data Processing:GE IS200IGPAG2AED has a high-performance processor by which high-speed data processing can be achieved. It can quickly collect, analyze and process a variety of data signals of the equipment being monitored, providing control system with timely and accurate data support. This could be done, for example, in a complex industrial production line, where the processing of the temperature, pressure and flow rate data helps to ensure the stable operation of the production process.

High-Quality Monitoring Ability: GE IS200IGPAG2AED has a stable monitoring function and can monitor the running state of the equipment in real time. It is capable of identifying abnormal condition of axial displacement and differential expansion of monitored equipment. At the same time, once the fault is found, it can send an alarm signal at any time to give the operator a prompt to take measures to deal with it, which can effectively avoid equipment failure and improve the reliability and safety of the whole system.

Installation

Installation preparation: Close the power of the relevant equipment before installation to prevent electric shock and equipment damage. Gather the required tools (screwdrivers/wire strippers, etc.). Verify that GE IS200IGPAG2AED Module is free from any physical damage or defect. Select a suitable location in the control cabinet or on the equipment. The installation location should be away from strong electromagnetic interference sources, with good heat dissipation conditions, and easy wiring and maintenance. It is advisable to be installed at position nearer to the monitored equipment as to minimize the signal cable length and enhance the accuracy of signal transmission. Keep consistent with the control cabinet or the equipment mounting hole, and use screws fixed. The module should be installed flat and stable to avoid vibration and displacement during operation, which can cause the module not to work properly.

Troubleshooting

NO SIGNAL OUTPUT: Check if the power supply is available, and whether the power indicator of the module is on. If there is no problem with the power supply, check whether the input signal line is loose or disconnected. Make sure the input signal parameters format is equivalent to the actual input signal format.

Wrong installation: To check whether the installation position of the sensor is correct, whether there is deviation or loosening. Make sure sensor is calibrated as per the calibration procedure in the manual. Detect if the measured object has abnormal vibration or displacement, affecting measurement accuracy. If the table 1 is excluded but the measurement is still not accurate, meaning that the module is having some issue and needs to be checked and calibrated further.

Communication Failure: Check for proper connections for the communication cable as well as damage or looseness. Ensure that the settings between the module and the attached device (e.g., baud rate, communication protocol) are configured correctly. Replace the communication cable or communication port to see if it can solve the problem. If the communication failure still exists, it may be due to the failure of the communication module of the device. Check and repair the communication module.

Application range

Power Generation Sector: GE IS200IGPAG2AED is utilized in thermal power plants to monitor the differential expansion and the shaft displacement of steam turbines. This ensures the safety and stability of the steam turbine, avoiding damage to the equipment due to excessive displacement or heat expansion. Such a method can be used in the monitoring system of hydro-generators in hydro-power plants, which can monitor the operating status of computers and related equipment in real time to provide data support for the optimal operation and maintenance of the hydro-power generation system.

Petrochemical: The application in petrochemical production process monitoring and control of rotating equipment such as pumps and compressors. GE IS200IGPAG2AED is generally used to check the key parameters of these equipment to ensure the normal operation of the equipment within the specified nominal range and to ensure that the equipment within the specified nominal displacement does not occur due to abnormal shaft displacement or vibration. It is also utilized in the safety monitoring system of petrochemical plants. And by continuously monitoring pipeline leaks in realtime and their various devices/exhaust location operating status, it can timely discover potential safety hazards, take preventive measures to avoid safety accidents.

Metallurgy: GE IS200IGPAG2AED used in the monitoring system of rolling mills in steel mills It realizes real-time monitoring of the running status of the rollers and motors in the rolling process, and detects shaft displacement and unbalanced load and other problems in the time which is conducive to improving the quality of steel products and the efficiency of the production line. In non-ferrous metal smelting, it can be used to monitor the smelting equipment to ensure the stable operation of the smelting process, and to improve the production efficiency and product quality.